Our Services

A full range of services for gas stations and oil depots
Instrumentation and Control and Diagnostics

Test and measurement instruments and automation

Diagnostics of Gas Station Control Systems

Comprehensive diagnostics of automation systems, fault detection, and verification of the proper functioning of sensors and controllers.

Calibrating Level Gauges

Configuration and calibration of Fafnir, TLS, and Torrex level meters. Programming parameters and verifying measurement accuracy.

Inspection of measuring instruments

Diagnostics of pressure, temperature, and flow sensors. Verification of measurement systems for compliance with standards.

Configuration of TRK Control Systems

Programming and configuring electronic control units for fuel dispensers.

Circuit and Interference Diagnostics

Verification of cable line integrity, shielding, and system noise immunity.

Installation and Commissioning

Installation and Configuration of Equipment

Installation of fuel dispensers

Installation of the Gilbarco fuel dispenser, connection to the tanks, configuration of the electronics, and commissioning.

Installation of level gauges

Installation of level sensors in tanks, laying of cable lines, and connection to the control system.

Installation of Pumping Equipment

Installation of submersible and surface pumps, commissioning, and performance testing.

Installation of oil depot components

Installation of valves, filters, meters, and filling systems. Comprehensive installation of process equipment.

Commissioning of metering systems

PLC/SCADA configuration, integration with databases and ERP systems, and verification of signals and communication protocols.

Maintenance and Repair

Scheduled maintenance and emergency repairs

Scheduled maintenance of fuel dispensers

Inspection of components, replacement of filters, cleaning, lubrication of mechanisms, leak testing, and testing of electronic components.

Repair of TRK Pumps

Diagnostics, disassembly, replacement of worn parts, reassembly, performance testing.

Repair of fuel meters

Restoring measurement accuracy, replacing metering components, and adjusting mechanisms.

Major repairs to tanks

Restoration of watertightness, anti-corrosion treatment, replacement of the bottom and sides, welding work.

Routine safety inspections

Periodic inspections, test reports, and monitoring of grounding and lightning protection systems.

Metrology Services

Equipment verification and calibration

Fuel Meter Calibration

Metrological verification of fuel meters, issuance of verification certificates, and entry into the state register.

Calibration of measuring equipment

Calibration of level gauges, pressure and temperature sensors, and flow meters. Preparation of calibration reports.

Verification of the accuracy of TRK dosing

Monitoring the accuracy of fuel dispensing, calibrating meters, and configuring dispensing systems.

Support for third-party audits

Preparing equipment and coordinating with metrology services during inspections.

Consulting Services

Expert assistance and training

Investigation into fuel losses

Analysis of accounting discrepancies, identification of the causes of losses, recommendations for resolving them, and verification of the system’s integrity.

Staff Training

Training gas station attendants on how to operate equipment and control systems, as well as on safety and operating procedures.

Technical Consultations

Consulting services on equipment selection, gas station upgrades, operational optimization, and regulatory compliance.

Technical Condition Audit of a Gas Station

Comprehensive equipment inspection, fault diagnosis, report preparation, and repair recommendations.

Preparation of technical specifications

Development of technical specifications for procurement, modernization, and automation of facilities; coordination of requirements.

Emergency Services

24/7 emergency support

24/7 Emergency Service

24/7 on-site service for emergency repairs and troubleshooting. Rapid response.

Emergency repairs to the shopping mall

Emergency restoration of fuel dispenser functionality in the event of malfunctions.

Repairing fuel leaks

Detection and repair of leaks in pipelines, tanks, and connections. Restoration of leak-tightness.

Restoration of automation systems

Emergency repairs to control systems, sensors, and controllers in the event of a malfunction.

Automation and Dispatching

SCADA, Telemetry, and Integration

SCADA and Telemetry

SCADA deployment, telemetry configuration, and real-time monitoring of tanks and pumping stations.

Integrations with accounting systems

Integration with ERP/1C, report exports, and an API for monitoring and analytics.

Automation of filling stations

PLC logic, inter-level interlocks, valve and pump control, overflow protection.

Engineering and Safety

Design, Auditing, and Occupational Safety

Design and Schematics

Electrical, instrumentation, and automation schematics; selection of cable routes and control cabinets.

Occupational Safety and Fire Safety

Safety briefings, logs, inspections of protective equipment, evacuation plans, and fire safety plans.

Technical inspection of facilities

A comprehensive audit of the current status, risks, and regulatory compliance, including a report and recommendations.

Certification and Documentation

Preparation of equipment certificates, test reports, and commissioning reports.

Order a service

Hours of Operation: Mon–Fri 9:00-18:00